[2022] New DES-4122 Dumps Questions - Valid Dumps Online To Prepare DES-4122 Exam Well
Earning Specialist - Implementation Engineer, PowerEdge Version 2.0 certification proves that you have ability to perform intermediate skill level tasks in installing, configuring, maintaining and troubleshooting Dell EMC PowerEdge Server products. Passing DES-4122 DELL EMC certification exam is the requirement of earning this certification. If you are a candidate who is preparing for DES-4122 Specialist - Implementation Engineer PowerEdge exam, you can choose to get new DES-4122 dumps questions to boost the full confidence to prepare for DELL EMC DES-4122 exam well. New DELL EMC DES-4122 exam dumps with actual questions and answers offered by the DumpsBase had been curated by the DELL EMC certified specialists and is deemed as the top-ranked study materials for the preparation of your Specialist - Implementation Engineer, PowerEdge DES-4122 Exam.
What is the process of completing Specialist - Implementation Engineer, PowerEdge Version 2.0 certification?
Specialist - Implementation Engineer, PowerEdge Version 2.0 certification is a special-level DELL EMC certification. As one candidate who is planning for it, he/she will be required to earn an associate-level certification first as listed:
● Dell Certified Professional – PowerEdge (Existing valid credentials only. Not available to earn anymore)
● Associate - PowerEdge Version 1.0
● Associate - PowerEdge Version 2.0 (DEA-41T1)
● Specialist – Implementation Engineer, PowerEdge Version 1.0
Then, pass DES-4122 Specialist - Implementation Engineer PowerEdge exam to earn the Specialist - Implementation Engineer, PowerEdge Version 2.0 certification. DES-4122 exam mainly focuses on installing, administering, and troubleshooting Dell EMC PowerEdge server products. It covers 6 sections:
Server Platforms (7%)
Server Components (25%)
Server Management and Configuration Tools (18%)
Server Troubleshooting and Maintenance (27%)
Server Security (10%)
Systems Management (13%)
Real DELL EMC DES-4122 exam contains two parts. Part 1 containing 54 questions which required to answer in 90 minutes and achieve 63% score. Part 2 containing 6 simulations which required to complete in 30 minutes and achieve 66% score. Only completing both the two parts indicates that you have pass the DELL EMC DES-4122 Specialist - Implementation Engineer, PowerEdge exam. New DES-4122 dumps questions are valid covering each exam section and topic for helping you prepare for Specialist - Implementation Engineer, PowerEdge exam. Study effectively and enhance your expertise, get the fundamentals in the DES-4122 exam dumps this can assist to improve your expertise efficiently.
What is the guranteed policy of new DELL EMC DES-4122 dumps questions?
New DELL EMC DES-4122 dumps questions of DumpsBase are valid, you'll be able to quickly pass your DES 4122 exam using the highest grades and become successful DELL EMC certified. At DumpsBase, you will not only get the valid DES-4122 exam dumps but 100% passing guarantee. We ensure that you can complete DES-4122 exam with the new and valid dumps questions, otherwise, you are able to also get the 100% money back assure on the Specialist - Implementation Engineer, PowerEdge DES-4122 pdf dumps. All in all DumpsBase DELL EMC DES-4122 exam dumps is your only source of preparation for the DES-4122 exam.
Besides, DES-4122 free dumps demo are available online also to help you check why we recommend new DES-4122 dumps questions below:
A technician is creating a virtual disk in the iDRAC (2x 4 TB NL-SAS in RAID 1) to install Windows 2016 They manually boot to the OS installation media without using the Lifecycle Controller OS Deployment wizard Only the first 2048 GB on the virtual disk can be partitioned.
How should the technician obtain access to the remaining 2 TB (approximately) of storage?
A. Use the Lifecycle Controller OS Deployment Wizard to deploy the OS on this server
B. Delete the 4 TB virtual disk and create a virtual (boot) disk no larger than 2048 GB
C. Upgrade to a newer version of the operating system
D. Use F2 to go into the BIOS, change the BIOS boot mode to UEFI, and try again
Answer: C
Where is the data stored to allow Easy Restore to successfully complete a system board replacement?
A. NAND Flash module on the disk drive mid plane
B. IDSDM SD card
C. vFlash SD card
D. Serial Flash storage in the server's front panel
Answer: C
A technician needs to repurpose a Dell EMC PowerEdge server. The server has dual processors with 18 cores each The OS only "sees" 24 threads in total.
Which setting should the technician change in Processor Settings in the System BIOS?
A. System Profile
B. Virtualization Technology
C. HyperThreading
D. Number of Cores per Processor
Answer: A
What are the default settings used when applying firmware and a configuration to a replaced part using the Lifecycle Controller?
A. Firmware: Upgrade to latest available version
Configuration Apply always
B. Firmware Allow version upgrade only
Configuration: Disabled
C. Firmware: Match firmware of replaced part
Configuration Apply always
D. Firmware Disabled
Configuration Apply only if firmware match
Answer: C
What is the purpose of the Silicon-Based Hardware Root of Trust feature in Dell EMC PowerEdge 14G servers?
A. Ensures that the installed operating system is authentic
B. Ensures that the server has a valid Service Tag number
C. Ensures that no unauthorized BIOS or firmware codes are run
D. Ensures that the server boots only when connected to a verified network
Answer: C
What is a systems management console solution optimized for monitoring and managing Dell enterprise and remote office hardware?
A. SupportAssist Enterprise
B. iSM
C. OpenManage Essentials
D. iDRAC9
Answer: C
After completing a disk rebuild operation, a technician needs to configure the system so that the rebuild process happens faster the expense of slowing users down.
Which setting should be changed?
A. Rebuild Rate in the BIOS settings
B. System Profile to Performance in the BIOS settings
C. System Profile to Performance in the iDRAC GUI
D. Rebuild Rate in the iDRAC GUI
Answer: D
A company that has very specific firmware requirements has acquired Dell EMC PowerEdge servers Any replaced parts of the type must match the original parts identically. The procedure must be as simple as possible with minimal risk.
What action should a technician take to help accomplish this goal?
A. Configure servers to access the remote firmware repository
B. Enable the Match Firmware of Replaced Part setting in the system BIOS
C. Install and configure a repository manager
D. Enable the Collect System Inventory On Restart (CSIOR) attribute
Answer: A
A technician installs eight servers into a fully operational rack with top of rack switch Each server has a quad 1Gb NIC and redundant power supplies. The company uses iDRAC in shared LOM mode with LOM1 as the selected NIC.
What should the technician do to verify iDRAC connectivity on each server?
A. iDRAC Datacenter license is installed.
B. Ethernet port LOM1 is cabled and the link light is green.
C. iDRAC dedicated NIC port is cabled and the link light is green
D. iDRAC Enterprise license is installed
Answer: C
Dell EMC PowerEdge 14G servers support which technology?
A. Quicksync 1.0
B. Intel Boot Guard
C. AMD GuardMI
D. iDRAC8
Answer: C
